Web Guiding System

Web guide atau web guiding system adalah alat yang digunakan untuk menjaga aligment substrat saat proses converting berlangsung. Kami memiliki produk All in one web guiding system untuk memudahkan proses guiding.

Kami juga memiliki spare part web guiding terpisah yang dapat disesuaikan dengan mesin industri anda.

All In One Web Guiding System

web guide system

Model

 W500, A100

Features

● One-piece design: tightly sealed, compact
● Brushless servo motor drive, maintenance-free
● Support three guiding of line, edge, and center
● Support photoelectric sensor, infrared sensor, ultrasonic sensor, CCD sensor
● Adopts variable PI adjustment algorithm, high precision, fast responding, with smaller error
● Precision ball screw, accurate positioning
● Super high response speed of 500 microsecond.
● Beautiful appearance: aluminum alloy finishing, surface sandblasting oxidation
● Flexible installation: can be integrated, separated and installed, can be installed at any angle

Web Guide Actuator

web guide actiator

Model

Servo Motor Actuator SE Series

Features

  • servo web guide actuator adopts Japan’s Sanyo electric motor as the actuator, without carbon brush
  • Fully reliable and long service life, truly realize long-term maintenance-free during use
  • Energy-saving and environmental-friendly,
  • Adopting Taiwan precision ball screw with the smallest gap
  • Clearance and durability, so that the actuator has no backlash error.
  • Choosing from75-300mm stroke, 0.5T-10T thrust weight
  • Installation method has direct connection type and L type

Web Sensor EPC/LPC

sn

Model

Edge Sensor A Series

Features

  • Adopting high-speed DSP chip, full digital processing, truly no drift, strong anti-interference ability
  • Adopting Japanese Fuji high-precision ultrasonic sensitive components with 0.01mm resolution
  • Fully sealed titanium alloy shell design with special surface treatment, to prevent dust and pollution, anti-corrosion
  • The ambient noise of the workshop has no effect on ultrasonic technology
  • It can detect any material (including mesh material) without adjustment
  • DC12V single power supply, 0-5V analog output, two switch output

Model

Edge Sensor AE Series

Features

  • No need for polarity conversion.
  • When the coil baseline and line asymptotically or the left and right edges are reversed, there is no need to switch the polarity of the control output.
  • No need to re-adjust the gain.
  • The deviation of the edge from the output voltage is not affected by the width or color of the line. Therefore, once the gain of the controller is set during the test run, there is no need to re-adjust the gain.
  • Position signal hold function.
  • When a line leaves the field of view and when it returns, the position signal generated immediately before the line leaves the field of view is maintained and output. Therefore, when the web bending speed is fast and the line (edge) will be out of the field of view, the tracking operation will be performed.
  • The line (edge) position is displayed by LED.
  • The control action, even if the integral action is standard, can also be combined with the position transmitter to perform proportional action. The most suitable control action can be selected according to the machine used.
  • When the detected edge is in the center of the field of view, an LED indicator lights up.
  • When the device is connected to a controller with a drive lock input, in the case of intermittent lines, when an interruption is detected in the line, the drive is locked and the tracking operation is stopped until the next line appears.

Web Guiding Controller

web guide system controller

Model

Web Controller S800 Series

Features

  • Adopting high-speed DSP chip, full digital processing, truly no drift, strong anti-interference ability
  • Adopting Japanese Fuji high-precision ultrasonic sensitive components with 0.01mm resolution
  • Fully sealed titanium alloy shell design with special surface treatment, to prevent dust and pollution, anti-corrosion
  • The ambient noise of the workshop has no effect on ultrasonic technology
  • It can detect any material (including mesh material) without adjustment
  • DC12V single power supply, 0-5V analog output, two switch output
Scroll to Top